← All guides
Energy

HVAC Controls: A Complete Guide

Published Nov 16, 2026

HVAC Controls: A Complete Guide

In short

HVAC controls are the sensors, controllers, actuators, and control logic that operate a building's heating, ventilation, and air conditioning equipment. They hold temperature, humidity, pressure, and airflow at setpoints, start and stop equipment on schedules, and coordinate air handlers, terminal units, and the central plant to meet comfort and ventilation needs with the least energy.

Heating, ventilation, and air conditioning uses more energy than any other system in most commercial buildings, and the controls decide how much of that energy does useful work. Two buildings with identical chillers, boilers, and air handlers can differ widely in consumption because of how their equipment is scheduled, sequenced, and reset. Most of the savings available in an existing building's HVAC system come from changes to control settings and logic, which cost little or nothing to make.

How do HVAC controls work?

Every HVAC control action follows the same loop: a sensor measures a condition, a controller compares the measurement with a setpoint, and an actuator adjusts equipment to close the gap. The following components make up that loop.

Sensors: Devices that measure temperature, humidity, pressure, airflow, carbon dioxide, and occupancy, and that confirm equipment status. A typical air handling unit carries sensors for supply, return, mixed, and outdoor air temperature, duct static pressure, and filter pressure drop.

Controllers: Devices that read sensor inputs, run control logic, and send outputs. A unitary controller runs a single terminal unit or rooftop unit. A programmable controller runs an air handler or a central plant and coordinates with other controllers over a network.

Actuators: Devices that move dampers and valves, plus the relays and variable frequency drives that start, stop, and modulate fans, pumps, and compressors.

Setpoints: The target values a controller holds, such as a zone temperature of 72°F or a duct static pressure of 1.2 inches of water column. Many setpoints are reset automatically as conditions change.

Control logic: The rules a controller follows, written down as a sequence of operation and translated into a controller program. The sequence states when equipment starts, how it stages, which setpoints it holds, and how those setpoints respond to load and weather.

Controls act at several levels at once. Local loops hold one variable at its setpoint within seconds. Equipment-level logic coordinates the loops inside one air handler or plant. Supervisory logic coordinates equipment across a building, for instance resetting an air handler's supply temperature according to requests from the terminal units downstream.

Which types of HVAC control exist?

Commercial buildings use several generations of control technology, frequently side by side in the same building.

Type How it works Where it is found
Standalone thermostats A wall device switches or stages one unit to a setpoint and schedule Small commercial buildings and packaged rooftop units
Pneumatic controls Compressed air carries signals and moves actuators, with mechanical logic in thermostats and receiver-controllers Older large buildings, often in terminal units and perimeter heating
Analog electronic controls Electronic sensors and controllers with fixed, hardwired logic Equipment-mounted controls and older retrofits
Direct digital control (DDC) Microprocessor controllers run programmed logic, log data, and communicate over a network The standard for commercial HVAC for several decades
Networked smart thermostats Thermostats with schedules, occupancy sensing, and remote access through a cloud service Small and mid-size buildings without a full building automation system

Direct digital control matters most for energy, because scheduling, setpoint resets, demand-controlled ventilation, and trend logging all depend on programmable controllers that read many sensors and communicate with each other. Pneumatic controls hold a setpoint reliably but cannot log data or reset setpoints from a central schedule, and many owners convert them in stages, often keeping pneumatic actuators and adding digital controllers to drive the existing actuators.

How does a control loop work?

Most HVAC control loops use feedback, measuring the result of their own action and correcting continuously. The difference between the measured value and the setpoint is the error, and the loop's job is to drive that error toward zero without overshooting or oscillating.

On-off control: The simplest form switches equipment fully on below a setpoint and fully off above it, with a differential between the two switching points to prevent rapid cycling. Thermostats on small units and many staging controls work this way.

Proportional control: The output moves in proportion to the error, so a zone a degree warm opens its cooling valve a little and a zone four degrees warm opens the valve further. Proportional control alone settles with a steady offset from the setpoint.

Proportional-integral (PI) control: The integral term accumulates the error over time and removes the offset. PI control runs most modulating loops in commercial HVAC, such as discharge air temperature, duct static pressure, and chilled water valve control.

Proportional-integral-derivative (PID) control: The derivative term responds to the rate of change. HVAC processes change slowly and sensor signals are noisy, so engineers seldom use the derivative term in building systems.

Poorly tuned loops cost energy and equipment life. A loop tuned too aggressively hunts around its setpoint, cycling valves, dampers, and drives continuously. A loop tuned too gently lets the controlled variable wander, so occupants feel the result before the controller corrects the error.

Deadbands between heating and cooling setpoints keep the two from operating at once. Section 6.4.3.1.2 of ASHRAE Standard 90.1 requires zone thermostatic controls that handle both heating and cooling to provide a deadband of at least 5°F, within which the supply of heating and cooling to the zone is shut off or reduced to a minimum.

Which control strategies save the most energy?

The control strategies that save the most energy match HVAC output to actual load, occupancy, and weather, where many buildings still run to design-day assumptions. A Pacific Northwest National Laboratory study of 34 control measures across 14 building types and 16 climate zones put the average potential at about 29 percent of US commercial building energy use. The Department of Energy's summary identifies better setpoints, lower minimum airflow at variable air volume boxes, and occupancy-based scheduling as the largest contributors.

The following strategies account for most of that potential:

  • Scheduling and optimal start: Running equipment only during occupied hours, with start times that adjust to outdoor conditions so each space reaches setpoint as occupants arrive
  • Setback and wider deadbands: Letting space temperatures drift further from comfort setpoints when spaces are unoccupied, and widening the band in which neither heating nor cooling runs
  • Supply air temperature reset: Raising the air handler's supply temperature when zones need less cooling, which cuts chiller energy and the reheat added to overcooled air
  • Duct static pressure reset: Lowering fan pressure until the terminal unit with the greatest need is nearly fully open, which reduces fan energy sharply because fan power falls faster than airflow
  • Airside economizing: Using cool outdoor air in place of mechanical cooling whenever outdoor conditions allow
  • Demand-controlled ventilation: Reducing outdoor air in partly occupied spaces, based on carbon dioxide or occupancy readings, while keeping the minimum ventilation the building requires
  • Lower terminal unit minimums: Reducing the minimum airflow each variable air volume box holds, which cuts fan energy and reheat
  • Plant resets and staging: Resetting chilled water, condenser water, and hot water temperatures with load, and staging chillers, boilers, and pumps to run each at an efficient operating point

Most of these strategies require no new equipment. They depend on sensors the building already has, on controllers able to run the logic, and on a sequence of operation that specifies the logic correctly.

How does ASHRAE Guideline 36 standardize HVAC sequences?

ASHRAE Guideline 36, High-Performance Sequences of Operation for HVAC Systems, publishes tested sequences for common HVAC systems, so engineers can specify proven logic by reference in place of writing a new sequence for every project. The guideline covers multiple-zone variable air volume air handlers, the terminal units they serve, and other common system types, and the current edition is Guideline 36-2024.

Guideline 36 relies on a small set of well-defined techniques. Trim-and-respond logic resets setpoints such as supply air temperature and duct static pressure according to the number of requests from downstream zones, so the most demanding zone sets the operating point while the rest of the system runs as efficiently as possible. Each sequence also includes alarms and fault detection rules for air handlers, so the document that specifies how equipment should run also defines tests for whether the equipment runs that way.

Research by Lawrence Berkeley National Laboratory supports the savings. A 2022 simulation study in the Journal of Building Performance Simulation found that Guideline 36 sequences reduced HVAC energy by an average of 31 percent against baseline sequences in a medium-sized office building. A 2026 field study presented at the ACEEE Summer Study measured air handler strategies, including supply air temperature reset, duct static pressure reset, and economizer control, across 17 projects in different building types and climate zones. HVAC savings ranged from 2 to 49 percent, with a median of 18 percent, and the projects achieved those savings by reprogramming existing controls, with no capital investment in new control infrastructure.

Why do HVAC controls drift from their design?

HVAC controls drift because the conditions they were set up for change while their settings stay the same, and because control loops compensate for failing components, hiding the failures from operators. A building can keep every zone comfortable while its controls waste a large share of the energy they manage.

The most common causes are the following:

  • Overrides left in place: Operators fix a point at a value to resolve a complaint or an emergency, and the override stays long after the problem has passed
  • Sensor drift and failure: A supply air sensor reading two degrees high leads the controller to overcool, and nothing in the control loop can detect the error
  • Stuck or leaking dampers and valves: Other equipment works harder to compensate, so the fault appears as higher energy use with no comfort complaint
  • Failed economizers: Dampers stuck closed waste free cooling, and dampers stuck open add heating and cooling load
  • Poorly tuned loops: Hunting loops wear out actuators and waste energy, and sluggish loops leave spaces uncomfortable
  • Schedules out of step with occupancy: Tenant moves, new working patterns, and holiday exceptions leave equipment running for empty floors
  • Sequences changed and never restored: Logic altered during troubleshooting or renovation remains in place for years

Economizers illustrate how widespread the problem is. A field study for the California Energy Commission's Public Interest Energy Research program, covering small commercial rooftop units in California buildings four years old or newer, found a total economizer failure rate of 64 percent. The causes ranged from mechanical and electrical failures and incorrect installation to drifting sensors and incorrect controller setup.

Drift is the reason retro-commissioning exists, and the reason fault detection and diagnostics software monitors control performance continuously between commissioning projects.

How do HVAC controls relate to a building management system?

HVAC controls make up most of what a building management system does, and the BMS adds the network, supervisory software, trend storage, and alarm handling that let a facilities team manage those controls across a building. In a building with a BMS, the field controllers run the HVAC control loops, and the supervisory layer coordinates equipment, holds schedules, and gives operators a single interface for setpoints and overrides. Field controllers keep running their programs if the supervisory layer fails.

Software above the BMS can adjust HVAC controls at the supervisory level, sending setpoint and schedule changes through the BMS with the owner's authorization. The loops themselves keep running in the field controllers.

How do HVAC controls affect comfort and indoor air quality?

HVAC controls determine comfort and indoor air quality as much as energy use, and the same settings frequently trade one against the other. Ventilation sequences have to deliver the outdoor air that ASHRAE Standard 62.1 requires for each space, and comfort targets are commonly set with reference to ASHRAE Standard 55, which defines acceptable thermal conditions for occupants.

Energy strategies stay within those limits when the controls are designed and maintained properly. Demand-controlled ventilation reduces outdoor air only toward the code minimum for the occupancy present. Supply air temperature reset raises the supply temperature only until a zone requests more cooling or humidity approaches its limit. Setbacks apply only to unoccupied hours, and optimal start returns spaces to setpoint before occupants arrive. Comfort complaints frequently point to a control problem that also wastes energy, such as a terminal unit damper stuck closed or a zone sensor mounted beside a heat source.

How should a team assess its HVAC controls?

The following checks apply to any installed HVAC control system, whether or not the building has a full building management system.

Documented sequences: A current sequence of operation for each system, written against Guideline 36 where possible, that matches the programs in the controllers.

Override inventory: A list of every point currently in manual override, with a reason and an owner for each.

Sensor accuracy: A calibration check of the sensors that drive major control decisions, starting with outdoor air, supply air, and mixed air temperature.

Economizer function: A functional test confirming that dampers move through their full range and that the changeover logic engages under the right outdoor conditions.

Loop performance: A trend review of the main modulating loops for hunting, sustained offset, or saturation at a limit.

Schedules: A comparison of equipment schedules with actual occupancy, including holiday exceptions and tenant after-hours requests.

Trend data: Enough logged points, at short enough intervals, to diagnose problems after the fact.

Where Noda fits

Noda is an agentic AI platform for commercial building operations that works as an always-on virtual building engineer, scaling engineering team capacity across every asset in a portfolio.

Noda works above the HVAC controls already installed in a building and leaves every control loop running in the field controllers. A Noda LaunchPad, an on-premise gateway at each site, reads the BMS over open protocols such as BACnet/IP and Modbus, and Noda maps the points it reads to a standard model of each building's equipment and how that equipment connects.

Noda's AI agents analyze the resulting trend data continuously and find the control problems described above: setpoints that have drifted, schedules running empty floors, resets that never engage, economizers that never economize, and loops working against each other. Each confirmed problem becomes a proposed change to a setpoint, schedule, or control sequence, with the evidence and an estimated annual saving, for an engineer to accept or decline. Where the owner grants write access, operators can set or override BMS points from Noda.

Automated Demand Management is the one case where Noda acts on HVAC equipment automatically, shedding or shifting load during a demand event on equipment configured and tested for that purpose.

The Intelligence Layer and Automated Demand Management pages describe both capabilities in more detail.

Frequently asked questions

  • Are HVAC controls the same as a building automation system?

    HVAC controls make up the largest part of a building automation system in most commercial buildings. A building automation system also covers lighting, metering, and integrated systems, and adds supervisory software, trend storage, and alarms. Smaller buildings frequently have HVAC controls with no building automation system at all, such as standalone thermostats on packaged rooftop units.

  • How is a thermostat different from an HVAC controller?

    A thermostat combines a temperature sensor, a setpoint, and simple on-off or staged control for one heating and cooling unit. An HVAC controller is a programmable device that reads many sensors and runs control logic for larger equipment, such as an air handling unit or a chiller plant, and usually communicates with other controllers over a building automation network.

  • Which sensors do HVAC controls use?

    The most common are temperature sensors for zones, supply air, return air, mixed air, outdoor air, and water loops. Systems also use humidity sensors, duct and building static pressure sensors, airflow stations, carbon dioxide sensors for ventilation control, occupancy sensors, and current sensors that confirm whether fans and pumps are running.

  • How do pneumatic controls differ from direct digital control?

    Pneumatic controls use compressed air as both the signal and the force that moves dampers and valves, with mechanical thermostats and receiver-controllers performing the logic. Direct digital control (DDC) uses microprocessor controllers that read electronic sensors, run programmed logic, and drive electric or pneumatic actuators. DDC supports scheduling, resets, trend logging, and network communication that pneumatic systems lack.

  • Should pneumatic controls be replaced?

    Many owners replace pneumatic controls during major renovations, or convert them in stages, because direct digital control enables scheduling, setpoint resets, trend data, and remote monitoring. Hybrid conversions keep pneumatic actuators in place and add digital controllers that send pneumatic signals, which lowers cost and disruption. The choice depends on the condition of the air compressor, tubing, and actuators.

  • How does a PID loop work in HVAC?

    A proportional-integral-derivative (PID) loop adjusts an output, such as a valve position, based on the difference between a measured value and its setpoint. The proportional term responds to the size of the error, the integral term removes the error that remains over time, and the derivative term reacts to how quickly the error is changing. Most HVAC loops run as proportional-integral loops, with the derivative term set to zero.

  • Why do HVAC control loops hunt?

    Hunting, a steady oscillation around the setpoint, usually means a loop is tuned too aggressively for the equipment it controls, or that an actuator is oversized, sticking, or responding slowly. Hunting wears out valves, dampers, and drives, wastes energy, and can mask real faults in trend data. Retuning the loop gains typically corrects the problem.

  • How much energy can better HVAC controls save?

    A 2017 Pacific Northwest National Laboratory study estimated that well-implemented controls could cut energy use in US commercial buildings by about 29 percent on average. A 2026 Lawrence Berkeley National Laboratory field study of ASHRAE Guideline 36 air handler sequences across 17 projects found median HVAC savings of 18 percent from reprogramming alone.

  • Does ASHRAE Guideline 36 require new hardware?

    Often not. Guideline 36 sequences run on standard direct digital controllers, and the Berkeley Lab field study of 17 projects reported its savings without capital investment in new control infrastructure. Some sequences depend on sensors or airflow measurement that older systems lack, so an assessment of the installed points comes first.

  • How does demand-controlled ventilation work?

    Demand-controlled ventilation adjusts the outdoor air an air handler brings in according to how many people occupy a space, usually measured by carbon dioxide sensors or occupancy counts. When a conference room or auditorium is partly empty, the system reduces outdoor air toward the minimum required for the building, which saves the energy that would otherwise heat or cool unneeded air.

  • How does an economizer save energy?

    An airside economizer opens the outdoor air dampers wider when outdoor air is cool and dry enough to cool the building, which reduces or eliminates mechanical cooling during mild weather. The controls compare outdoor and return air temperature or enthalpy to decide when to economize. Failed dampers, actuators, and sensors are a common reason economizers save far less than designed.

  • How does supply air temperature reset work?

    Supply air temperature reset raises the temperature of the air an air handler delivers when the zones it serves need less cooling, and lowers it when they need more. Warmer supply air reduces chiller energy and the reheat that terminal units add to overcooled air. Guideline 36 uses a trim-and-respond method that adjusts the setpoint according to how many zones request cooling.

  • Why do heating and cooling sometimes run at the same time?

    Simultaneous heating and cooling occurs when control settings or faults set two systems against each other: a zone reheats air that the air handler overcooled, adjacent units with separate thermostats fight over a shared space, or a leaking valve lets hot water into a coil that should be idle. Deadbands between heating and cooling setpoints, coordinated sequences, and fault detection prevent most of these cases.

  • Who programs HVAC controls?

    Controls contractors and systems integrators write and change control programs, usually with manufacturer-specific programming tools. Facilities teams adjust setpoints and schedules through the operator interface. Engineers write the sequences of operation that the programs implement, and commissioning agents test whether the installed programs match those sequences.

  • How often should HVAC controls be checked?

    Control performance degrades continuously after commissioning as overrides accumulate, sensors drift, and occupancy changes. ENERGY STAR guidance puts recommissioning on a three-to-five-year cycle, and many owners add continuous monitoring, such as fault detection software, to catch control problems in the years between.

  • Can AI control HVAC equipment?

    AI software operates at the supervisory level, issuing new setpoints and schedules to the building automation system where the owner authorizes write access. Local control loops remain in the field controllers. In most deployments, a person reviews and accepts proposed changes, and automatic action is limited to defined cases such as demand events.